Cover Image

Advances on Mechanics, Design Engineering and Manufacturing III : Proceedings of the International Joint Conference on Mechanics, Design Engineering and Advanced Manufacturing, JCM 2020, June 2-4 2020.

Bibliographic Details
Main Author: Roucoules, Lionel.
Other Authors: Paredes, Manuel., Eynard, Benoit., Morer Camo, Paz., Rizzi, Caterina.
Format: eBook
Language:English
Published: Cham : Springer International Publishing AG, 2021.
Edition:1st ed.
Series:Lecture Notes in Mechanical Engineering Series
Subjects:
Electronic books.
Online Access:Click to View
Table of Contents:
  • Intro
  • Preface
  • Organization Committee JCM 2020 Members
  • Conference Chair
  • Conference Program Chair
  • Conference Advisory Chairmen
  • Scientific Committee
  • Organizing Committee
  • Contents
  • Manufacturing Engineering
  • Designing Powder Metallurgy Process - The Influence of High Sintering Temperature on Dimensional and Geometrical Precision
  • 1 Introduction
  • 2 Experimental Procedure
  • 3 Results and Discussion
  • 3.1 Dimensional Precision
  • 3.2 Geometrical Precision
  • 4 Conclusions
  • References
  • Process Parameters Effect on Weld Beads Geometry Deposited by Wire and Arc Additive Manufacturing (WAAM)
  • 1 Introduction
  • 2 Experimental Setup
  • 3 Results and Discussion
  • 3.1 Temperature Evolution
  • 4 Geometry Evolution
  • 5 Conclusion
  • References
  • A Parametric Study of Additive Manufacturing Process: TA6V Laser Wire Metal Deposition
  • 1 Introduction
  • 2 Protocol of Experiments
  • 2.1 Model and Variables
  • 2.2 Methods
  • 2.3 Taguchi's Experimental Design
  • 3 Results and Analysis
  • 3.1 Correlation Coefficient
  • 3.2 Variance Analysis
  • 4 Conclusion
  • References
  • Develop Model for Controlled Depth Milling by Abrasive Water Jet of Ti6Al4V at Jet Inclination Angle
  • 1 Introduction
  • 2 Proposed Model with the Inclination Angle of the Jet
  • 3 Experiment
  • 4 Result
  • 5 Conclusion
  • References
  • Simulation and Experimental Validation of Secondary Dendrite Arm Spacing for AlSi7Mg0.3 Chassis Parts in Low Pressure Die Casting
  • 1 Introduction
  • 2 Secondary Dendrite Arm Spacing Analysis
  • 2.1 Low Pressure Die Casting Simulation
  • 2.2 Spectrochemical Analysis with Optical Emission Spectroscopy
  • 2.3 SDAS Mapping Through Micrographs
  • 2.4 Correlation Between Measured and Simulated SDAS
  • 3 Experiments and Simulation Analysis on Case Studies
  • 4 Conclusions
  • References.
  • Influence of the Hole Surface Integrity on the Fatigue Strength of an Aluminium Drilled Part
  • 1 Introduction
  • 2 Experimental Work
  • 2.1 Fatigue Tests
  • 2.2 Surface Integrity Characterization
  • 3 Discussion and Conclusions
  • References
  • Cold Working Process on Hard Metal Stacked Assembly
  • 1 Introduction
  • 2 Stacked Cold Expansion Process
  • 3 Experimental Campaign
  • 4 Results
  • 5 Conclusion and Perspectives
  • References
  • Numerical Simulation and Experimentation of Additive Manufacturing Processes with Polyurethane Foams
  • 1 Introduction
  • 2 Foam Polyurethane Characterization
  • 3 Comparison Between Experiments and Numerical Simulation
  • 4 Use of Simulation to Apply a Speed Correction on a Trajectory in Order to Minimize the Form Defect
  • 5 Perspectives
  • 6 Conclusion
  • References
  • Analysis of Warpage Induced by Thick Copper Metal on Semiconductor Device
  • 1 Introduction
  • 2 Sample and Test Description
  • 3 Warpage Measurements
  • 4 Finite Element Model
  • 5 Conclusions
  • References
  • Finite Element Modeling and Validation of Metal Deposition in Wire Arc Additive Manufacturing
  • 1 Introduction
  • 2 Proposed FE Metal Deposition Technique
  • 2.1 Metal Deposition Modelling
  • 2.2 Heat Input Modelling
  • 2.3 Model Update
  • 3 Validation
  • 3.1 Results
  • 4 Conclusions
  • References
  • Study of the Use of Sawdust and Mycelium Composite as a Substitute of EPS
  • 1 Introduction
  • 2 Materials and Methods
  • 3 Results and Discussion
  • 4 Conclusions
  • References
  • Topology Optimization Design of Internal Reinforcements in a Sailing Dinghy
  • 1 Introduction
  • 2 Methods
  • 3 Case Study
  • 3.1 Discussion
  • 4 Conclusions
  • References
  • State of the Art on Robust Design Methods for Additive Manufacturing
  • 1 Introduction
  • 2 State of the Art
  • 2.1 Robust Design
  • 2.2 Robust Design for Additive Manufacturing.
  • 3 Conclusions and Perspectives
  • References
  • Topological Optimization of a Mechanical System with Adaptive Convergence Criterion
  • 1 Introduction
  • 2 The TOMS Method
  • 3 Adaptive Coefficient of Convergence Ε
  • 4 Conclusion and Perspectives
  • References
  • Design for Additive Manufacturing of a Topology Optimized Brake Caliper Through CAD-Platform-Based Systematic Approach
  • 1 Introduction
  • 2 Method
  • 3 Case Study
  • 3.1 Product Planning
  • 3.2 Design
  • 4 Results and Discussion
  • References
  • Product and System Engineering
  • Evaluation of the Effects Caused by Mandibular Advancement Devices Using a Numerical Simulation Model
  • 1 Introduction and Literature Review
  • 2 Materials and Methods
  • 2.1 Anatomical Model
  • 2.2 Materials
  • 2.3 Boundary Conditions
  • 2.4 Meshing
  • 3 Results and Discussions
  • 4 Conclusions
  • References
  • Simulation of Dynamic Stresses on High Performance Engine Valve Spring System Considering Coil Clashing Effect
  • 1 Introduction
  • 2 Testing Equipment
  • 3 Multibody Dynamic Models
  • 4 Finite Element Dynamic Model
  • 5 Results
  • 6 Conclusion
  • References
  • Thread Couplings Stress Analysis by Radial Basis Functions Mesh Morphing
  • 1 Introduction
  • 2 Discretized Models
  • 3 Parameterization
  • 4 Results and Discussion
  • 5 Conclusions
  • References
  • Computer-Aided Tolerancing Analysis of a High-Performance Car Engine Assembly
  • 1 Introduction
  • 2 Method
  • 3 Case Study: V12 Engine Assembly
  • 4 Discussion and Conclusions
  • References
  • Review of Product Design and Manufacturing Methods for Prosumers
  • 1 Introduction
  • 2 Methodological Description
  • 3 Results
  • 4 Conclusions
  • References
  • State of the Art for Evaluation of Inventive Design Solution Concepts
  • 1 Introduction
  • 2 Aim and Scope
  • 3 Inventive Design Solution Concepts
  • 3.1 Inventive Design Definition.
  • 3.2 Our Position in Inventive Design Process
  • 3.3 Inventive Design Solution Concept Evaluation
  • 3.4 Research Gaps in Inventive Design Solution Concept Evaluation
  • 4 Conclusion and Future Research
  • References
  • Systemic Approach for Local Energy Mix Assessment
  • 1 Introduction
  • 2 Methodology
  • 2.1 Simulation
  • 2.2 Control Strategies
  • 3 Case Study
  • 4 Conclusion
  • References
  • Towards a Better Understanding of Open Source Hardware Design Reuse in Company-Community Collaboration
  • 1 Introduction
  • 2 Design Reuse in Company and Community
  • 2.1 Design Reuse in Companies
  • 2.2 Design Reuse in Communities
  • 3 Design Reuse in Company-Community Collaboration
  • 4 Conclusions
  • References
  • Comfort Driven Redesign: The Case of Library Chairs
  • 1 Introduction
  • 2 Materials and Method
  • 2.1 Design from Experiment
  • 2.2 Redesign of Library Chair
  • 2.3 Experiment Setup
  • 2.4 Participants
  • 2.5 Questionnaires
  • 2.6 Experiment Protocol
  • 3 Results
  • 4 Conclusions
  • References
  • Constraint Analysis and Optimization of NES System Based on Variable Pitch Spring
  • 1 Introduction
  • 2 NES Design Process
  • 3 Nonlinear Constraint Analysis
  • 4 Optimization Result
  • 5 Conclusions
  • References
  • Generative Design in the Transmission System of a Skateboard
  • 1 Introduction
  • 2 Materials and Methods
  • 3 Results
  • 4 Discussion
  • 5 Conclusions
  • References
  • Methodology of Product Sustainable Redesign. Case Study: Furniture of a Clothing Retail Store
  • 1 Introduction
  • 2 Methodology
  • 3 Case Study
  • 4 Conclusions
  • References
  • Enhanced Material-Driven Design Methodology: Luffa Cylindrica's Case
  • 1 Introduction
  • 2 Methodology
  • 3 Phase I: Luffa Cylindrica Understanding
  • 3.1 Volumetric Characterization
  • 3.2 Mechanical Characterization
  • 3.3 Other Properties
  • 4 Phase II: Conceptualization.
  • 5 Phase III and IV: Development and Prototyping
  • 6 Conclusions
  • References
  • A Well-to-Wheel Comparative Life Cycle Assessment Between Full Electric and Traditional Petrol Engines in the European Context
  • 1 Introduction
  • 2 Materials and Methods
  • 3 Results and Discussion
  • 4 Conclusions
  • References
  • Product Eco-Design in the Era of Circular Economy: Experiences in the Design of Espresso Coffee Machines
  • 1 Introduction
  • 2 Product Eco-Design for Coffee Machines
  • 3 Case Studies
  • 4 Conclusions
  • References
  • A Novel Procedure to Design a Positionable and Stable Drilling Template for Spine Surgery
  • 1 Introduction
  • 2 Methodology
  • 3 Conclusion
  • References
  • CAD and Interaction
  • Feature-Based Modelling of Laryngoscope Blades for Customized Applications
  • 1 Introduction
  • 2 Materials and Methods
  • 2.1 Parametrization
  • 2.2 Parametric Modelling
  • 2.3 Mechanical Tests
  • 2.4 Additive Manufacturing of a Laryngoscope Prototype
  • 3 Results and Discussion
  • References
  • Magnitude Finger Forces Analysis During Simulating Pseudo-Haptic Spring
  • 1 Introduction
  • 2 Experimental Protocol and Participants
  • 3 Results and Discussion
  • 4 Conclusion
  • References
  • Parametric Hull Design with Rational Bézier Curves
  • 1 Introduction
  • 2 Design Approach
  • 3 Case Study
  • 4 Conclusion
  • References
  • A Framework for Curvature-Based CAD Mesh Partitioning
  • 1 Introduction
  • 2 Related Work
  • 3 Curvature-Based Framework for ISO GPS Partitioning
  • 3.1 Initial Region Partition
  • 3.2 Region Refinement
  • 4 Case Study
  • 5 Conclusion
  • References
  • A Topology Optimization Method for Stochastic Lattice Structures
  • 1 Introduction
  • 2 Materials and Methods
  • 2.1 The Algorithm
  • 2.2 The Case Study
  • 3 Results and Discussion
  • 4 Conclusions
  • References.
  • Generative Design for Additively Manufactured Textiles in Orthopaedic Applications.

Similar Items